| Overall Rating: |
|
2
out of 5
|
hitch,
August 4, 2009
By tomm12
from florida
|
Pros: easy installation
Cons: The photo does not represent the hitch that i was expecting,disapointed but it will have to do.Not to HAPPY!
"OK!If I known the hitch that arrived was not the same as the photo,I would'nt have bought it.I kept it because I need it.Just hope it holds up."
|
|
How often do you shop at JC Whitney.com?:
Multiple Times a Year
|
|
Review 2 for HIDDEN HITCH® CLASS III 2" RECEIVER HITCHES FOR JEEP®
| Overall Rating: |
|
4
out of 5
|
Great,
November 10, 2008
By Impulse
from Syracuse, NY
|
Pros: Extremely easy installation
Cons: Looks nothing like the picture
"The installation for this product is so, so, so, easy. 4 bolts and that's it. Take's about 10 to 15 minutes. Don't be dooped by the picture though it look's nothing like it and none of the accessories in the picture come with it. Overall I would recommend this to anyone!!!!"
|
|
How often do you shop at JC Whitney.com?:
Multiple Times a Year
|
|
Review 3 for HIDDEN HITCH® CLASS III 2" RECEIVER HITCHES FOR JEEP®
|
Review 4 for HIDDEN HITCH® CLASS III 2" RECEIVER HITCHES FOR JEEP®
|
Review 5 for HIDDEN HITCH® CLASS III 2" RECEIVER HITCHES FOR JEEP®
|
Review 6 for HIDDEN HITCH® CLASS III 2" RECEIVER HITCHES FOR JEEP®
|
Review 7 for HIDDEN HITCH® CLASS III 2" RECEIVER HITCHES FOR JEEP®
| Overall Rating: |
|
5
out of 5
|
2007 Wrangler X installation ease,
May 3, 2007
By HSVMark
from Huntsville, Alabama
| Ease of Use/Installation: |
|
5
out of 5
|
| Features: |
|
4
out of 5
|
|
"Though not like the advertised picture, this receiver hitch was way too easy to install. Removed the old tow bar and 3 mounting bolts, then replaced with hitch with included 4 mounting bolts and washers. Placing bolts above muffler and feeding into four pre-drilled holes allowed the hitch to be installed in under 30 minutes. Muffler did not have to be lowered or moved. I could have made it under 15 minutes, instead I had to grind a oversize weld off the front of the crossmember to get the hitch assembly to fit properly. An air grinder with round stone did the trick here. Torgue of bolts requires 75 Ft lbs (900 in lbs) and I only have a 750 in lb torque wrench...so I need to borrow a torque wrench to do the final tightening. Overall, a very good product. Prior to ordering I was wondering how the pictured hitch would mount. I crawled under the back bumper and discovered a hefty crossmember across the back of the jeep. Well folks, that's where it mounts to. Picture a receiver tube with two vertical 1/4 inch plates welded to it, front and back with four holes for mounting...there you go...the hitch. Now for the negative...only thing I see is if you get off-road alot, the receiver sticks out about 6 inches behind the bumper and the 2 inch tube is below stock bumper. You loose a little rear incline clearance. Just weight the alternative...pull a boat or trailer or go 4 wheeling. I needed the boat pulling capability. With only 4 bolts, it would be easy to remove for those special off-road occasions. I would recommend this Class III hitch to all 2007 Wrangler X owners."
|
|
How often do you shop at JC Whitney.com?:
Once a Year
|
|
Review 8 for HIDDEN HITCH® CLASS III 2" RECEIVER HITCHES FOR JEEP®
|
Review 9 for HIDDEN HITCH® CLASS III 2" RECEIVER HITCHES FOR JEEP®
3 of 3 people found this review helpful.
|
Review 10 for HIDDEN HITCH® CLASS III 2" RECEIVER HITCHES FOR JEEP®
|